Fundamental mechanical and creep behavior of minerals at elevated temperatures is relevant to many subsurface exploration and resource recovery processes, yet remains largely elusive. This study uses instrumented indentation to measure microscale deformation and nanoscale creep of biotite, albite, and quartz, which are the major mineral phases of granitic rocks, at temperatures up to 400 °C. The results show that the elastic modulus of biotite is not only the lowest at room temperature but also decays the most at elevated temperature (i.e., by 25% reduction at 400 °C) compared to that of albite and quartz. The creep deformation within 20 s doubles when the temperature increases from 20 °C to 400 °C for albite, quartz, and biotite, and biotite showed at least three times the overall creep deformation compared to quartz and albite under the same temperature. The indentation creep deformation can be well characterized using a logarithmic time model, showing both transient and constant-rate creep deformation. The secondary creep rate for biotite is about three times that of albite and quartz at the same temperature, and as the temperature increases from 20 °C to 400 °C, the rate of secondary creep becomes approximately 10 times faster for the three tested minerals. Both transient creep deformation and the rate of secondary creep can be empirically correlated to the elastic moduli, which allows quick estimates of the temperature-dependent creep behavior of granitic minerals using their elastic properties, especially when those creep constants are not readily available at elevated temperatures. These results enhance the understanding of temperature-dependent creep deformation at small scales and provide insight into mineral-level damage in granitic rocks due to temperature and long-term deformation.

Ceramic aerogels are promising lightweight and high-efficient thermal insulators for applications in buildings, industry, and aerospace vehicles but are usually limited by their brittleness and structural collapse at high temperatures. In recent years, fabricating nanostructure-based ultralight materials has been proved to be an effective way to realize the resilience of ceramic aerogels. However, the randomly distributed macroscale pores in these architectures usually lead to low stiffness and reduced thermal insulation performance. Here, to overcome these obstacles, a SiC@SiO2 nanowire aerogel with a nanowire-assembled anisotropic and hierarchical microstructure was prepared by using directional freeze casting and subsequent heat treatment. The aerogel exhibits an ultralow thermal conductivity of ~14 mW/m·K, an exceptional high stiffness (a specific modulus of ~24.7 kN·m/kg), and excellent thermal and chemical stabilities even under heating at 1200°C by a butane blow torch, which makes it an ideal thermally superinsulating material for applications under extreme conditions.

The catalytic performance of core-shell platinum alloy nanoparticles is typically superior to that of pure platinum nanoparticles for the oxygen reduction reaction in fuel cell cathodes. Thorough understanding of core-shell formation is critical for atomic-scale design and control of the platinum shell, which is known to be the structural feature responsible for the enhancement. Here we reveal details of a counter-intuitive core-shell formation process in platinum-cobalt nanoparticles at elevated temperature under oxygen at atmospheric pressure, by using advanced in situ electron microscopy. Initial segregation of a thin platinum, rather than cobalt oxide, surface layer occurs concurrently with ordering of the intermetallic core, followed by the layer-by-layer growth of a platinum shell via Ostwald ripening during the oxygen annealing treatment. Calculations based on density functional theory demonstrate that this process follows an energetically favourable path. These findings are expected to be useful for the future design of structured platinum alloy nanocatalysts.Core-shell platinum alloy nanoparticles are promising catalysts for oxygen reduction, however a deeper understanding of core-shell formation is still required. Here the authors report oxygen-driven formation of core-shell Pt₃Co nanoparticles, seen at the atomic scale with in situ electron microscopy at ambient pressure.

Advanced electrocatalysts with low platinum content, high activity and durability for the oxygen reduction reaction can benefit the widespread commercial use of fuel cell technology. Here, we report a platinum-trimer decorated cobalt-palladium core-shell nanocatalyst with a low platinum loading of only 2.4 wt% for the use in alkaline fuel cell cathodes. This ternary catalyst shows a mass activity that is enhanced by a factor of 30.6 relative to a commercial platinum catalyst, which is attributed to the unique charge localization induced by platinum-trimer decoration. The high stability of the decorated trimers endows the catalyst with an outstanding durability, maintaining decent electrocatalytic activity with no degradation for more than 322,000 potential cycles in alkaline electrolyte. These findings are expected to be useful for surface engineering and design of advanced fuel cell catalysts with atomic-scale platinum decoration.

The catalytic performance of core-shell platinum alloy nanoparticles is typically superior to that of pure platinum nanoparticles for the oxygen reduction reaction in fuel cell cathodes. Thorough understanding of core-shell formation is critical for atomic-scale design and control of the platinum shell, which is known to be the structural feature responsible for the enhancement. Here we reveal details of a counter-intuitive core-shell formation process in platinum-cobalt nanoparticles at elevated temperature under oxygen at atmospheric pressure, by using advanced in situ electron microscopy. Initial segregation of a thin platinum, rather than cobalt oxide, surface layer occurs concurrently with ordering of the intermetallic core, followed by the layer-by-layer growth of a platinum shell via Ostwald ripening during the oxygen annealing treatment. Calculations based on density functional theory demonstrate that this process follows an energetically favourable path. These findings are expected to be useful for the future design of structured platinum alloy nanocatalysts.Core-shell platinum alloy nanoparticles are promising catalysts for oxygen reduction, however a deeper understanding of core-shell formation is still required. Here the authors report oxygen-driven formation of core-shell Pt3Co nanoparticles, seen at the atomic scale with in situ electron microscopy at ambient pressure.

Advanced electrocatalysts with low platinum content, high activity and durability for the oxygen reduction reaction can benefit the widespread commercial use of fuel cell technology. Here, we report a platinum-trimer decorated cobalt-palladium core-shell nanocatalyst with a low platinum loading of only 2.4 wt% for the use in alkaline fuel cell cathodes. This ternary catalyst shows a mass activity that is enhanced by a factor of 30.6 relative to a commercial platinum catalyst, which is attributed to the unique charge localization induced by platinum-trimer decoration. The high stability of the decorated trimers endows the catalyst with an outstanding durability, maintaining decent electrocatalytic activity with no degradation for more than 322,000 potential cycles in alkaline electrolyte. These findings are expected to be useful for surface engineering and design of advanced fuel cell catalysts with atomic-scale platinum decoration.

Nb2O5 is a Li+ intercalation metal oxide that is of current interest for lithium ion battery electrodes. The electrophoretic deposition (ED) of Nb2O5 thin-films from aqueous, NbOx colloidal solutions is reported here. For films ranging in thickness from 38 to 144 nm, the mass loading of Nb2O5 on the electrode is correlated with the coulometry of ED using quartz crystal microbalance gravimetry. Crystalline, phase pure films of orthorhombic, T-Nb2O5, are obtained by postdeposition calcination. These films exhibit unusually high specific capacities for Li+-based energy storage as a consequence of ≈70% porosity. For example, a 60 nm thick film displays a specific capacity, Csp, of 420 mAh/g at 5 A/g and 220 mAh/g at 50 A/g, which can be compared with the theoretical Faradaic capacity of 202 mAh/g. T-Nb2O5 films also have a specific energy density in the range from 770-486 Wh/kg, and a specific power density in the range from 9 to 90 kW/kg. These excellent energy storage metrics are attributed to augmentation of the Faradaic capacity by high double-layer capacities enabled by the mesoporous structure of these films.

Mimicking the zonal organization of native articular cartilage, which is essential for proper tissue functions, has remained a challenge. In this study, a thermoresponsive copolymer of chitosan-g-poly(N-isopropylacrylamide) (CS-g-PNIPAAm) was synthesized as a carrier of mesenchymal stem cells (MSCs) to provide a support for their proliferation and differentiation. Microengineered three-dimensional (3D) cell-laden CS-g-PNIPAAm hydrogels with different microstripe widths were fabricated to control cellular alignment and elongation in order to mimic the superficial zone of natural cartilage. Biochemical assays showed six- and sevenfold increment in secretion of glycosaminoglycans (GAGs) and total collagen from MSCs encapsulated within the synthesized hydrogel after 28 days incubation in chondrogenic medium. Chondrogenic differentiation was also verified qualitatively by histological and immunohistochemical assessments. It was found that 75 ± 6% of cells encapsulated within 50 μm wide microstripes were aligned with an aspect ratio of 2.07 ± 0.16 at day 5, which was more organized than those observed in unpatterned constructs (12 ± 7% alignment and a shape index of 1.20 ± 0.07). The microengineered constructs mimicked the cell shape and organization in the superficial zone of cartilage whiles the unpatterned one resembled the middle zone. Our results suggest that microfabrication of 3D cell-laden thermosensitive hydrogels is a promising platform for creating biomimetic structures leading to more successful multi-zonal cartilage tissue engineering. Biotechnol. Bioeng. 2017;114: 217-231. © 2016 Wiley Periodicals, Inc.

Amidoxime-functionalized polymeric adsorbents are the current state-of-the-art materials for collecting uranium (U) from seawater. However, marine tests show that vanadium (V) is preferentially extracted over U and many other cations. Herein, we report a complementary and comprehensive investigation integrating ab initio simulations with thermochemical titrations and XAFS spectroscopy to understand the unusually strong and selective binding of V by polyamidoximes. While the open-chain amidoxime functionalities do not bind V, the cyclic imide-dioxime group of the adsorbent forms a peculiar non-oxido V⁵⁺ complex, exhibiting the highest stability constant value ever observed for the V⁵⁺ species. XAFS analysis of adsorbents following deployment in environmental seawater confirms V binding solely by the imide-dioximes. Our fundamental findings offer not only guidance for future optimization of selectivity in amidoxime-based sorbent materials, but may also afford insight to understanding the extensive accumulation of V in some marine organisms.